"Obviously Better Layout That Emphasizes Stick Handling" Makes me think of a Hockey stick arcade stick.
Which would be a feat, especially if it was usable as a hockey stick too. And Awesome. It would be sooooo awesome.
"Obviously Better Layout That Emphasizes Stick Handling" Makes me think of a Hockey stick arcade stick.
Which would be a feat, especially if it was usable as a hockey stick too. And Awesome. It would be sooooo awesome.
Binged All Of Gundam In 4 Years, 1 Week and All I Got Was This Stupid Mask
FF XIV: Walked to the End
Started Legend of the Galactic Heroes (14/07/23), pray for me.
Kitty!
<NEW FIC!> Revolution #9: Somewhere out there, there's a universe in which your mistakes and failures never happened, and all you wished for is true. How hard would you fight to make that real?
[11:20:46 AM] GlowStiks: lucina is supes attractive
[12:40] Lace: lucina is amazing
[12:40] Neir: lucina is pretty much flawless
Okay... on my most current design, I decided to get rid of the HitBox(tm) layout- if only because I couldn't make it aesthetically pleasing.
Here's my initial image to use for the top panels. I'm looking for other images of these two to use as well.
Spoiler:
Last edited by Epiren; December 7th, 2015 at 06:49 AM.
The second draft of the case:
Spoiler:
Here's the innards for my project box:
Of note - I'm terrible at woodwork.
Last edited by Epiren; January 12th, 2015 at 07:21 PM.
Okay, I've completed designs for my artwork:
Spoilered for size
But onto the fun stuff - here's a hint to my next stick:
Spoiler:
Last edited by Epiren; January 12th, 2015 at 07:42 PM.
I'm really bad at trying to focus on one project.
Here's an impulsive build - theme: Cupid's Bow:
Spoiler:
Last edited by Epiren; December 7th, 2015 at 06:49 AM.
Your dedication to fight sticks is commendable.
Thanks.Originally Posted by Strife
And here it is, wired!
Front
Spoiler:
Last edited by Epiren; December 7th, 2015 at 06:50 AM.
Don't the wires sticking out the back mess with the way its held? You cant hold it like a bow, since you'd be crushing the wire when holding it, and you cant really sit it on your lap for the same reason, plus the bowstring.
Binged All Of Gundam In 4 Years, 1 Week and All I Got Was This Stupid Mask
FF XIV: Walked to the End
Started Legend of the Galactic Heroes (14/07/23), pray for me.
...
......
.........
If I were making practical sticks, then I would be worried. However, I'm planning on bending the metal prongs so that they're more-or-less 90 deg to the side, which drastically changes the wires' directions. So at the very least, they aren't pointing towards me.
As for position, I'll probably have it between my legs, with the bottom point on the ground. I plan on a greater bend to the bow's arc, so I'll at least have a greater buffer too.
(Making excuses as I go)
So holding it like a cello or that santa you did? Interesting, though it would be cool if you managed to play standing and holding it like you were about to shoot. And maybe maining an archer character like Hawkeye in UMvC3.
Binged All Of Gundam In 4 Years, 1 Week and All I Got Was This Stupid Mask
FF XIV: Walked to the End
Started Legend of the Galactic Heroes (14/07/23), pray for me.
After putting it off for 3 or so months, I finally finished the painting/curing portion of the box.
... though I might have messed up on the bondo part...
... I just noticed that I didn't even post the completed stick's pics...
Well, it's been done for a couple of months now.
Material:
Wood: 1/2" MDF & 1/8" Plywood
Clear 1/16" Plexiglass - 5" x 15.5"
24 mm screw-in Seimitsu Buttons (9) - Addendum: due to the stick placing, I had to remove the L2 and R2 (LT and RT) buttons.
JLF Sanwa stick (Quick Release) - with bottom support.
Kaimana LEDs (6)
Kaimana PCB
PS360+
Rare-Earth Neo something magnets (A lot)
2 Hinges
Metal Picture Supports/Bar (4)
Spoiler:
Notes:
Rather than using screws to fasten everything, I decided not to. For the base itself, I affixed everything with Bondo and 1/2" Dia wooden shafts. For the top panels, I glued strips of metal onto their undersides and then glued the metal supports to the sides. 1/4" Dia magnets then kept everything together. The hinges were glued to the bottom of the buttons' panel, held in place with 2 1/2" Dia magnets. Those magnets are really annoying to pull apart.
I tried going for a mirror coat with paint, but due to the poor handling with Bondo, I decided not to. Maybe next time. Also, I broke the plexi a number of times. That wasn't pleasant. While the hole for the stick is in the center, the stick itself was not, so I had to grind away at the wood. I modded it with LEDs as well, so that it will gradually change colors from Red to Violet to Red again.
Last edited by Epiren; December 7th, 2015 at 06:51 AM.
Heh, that pic with the rubber protector makes archer look naked. Turns it into a completely different picture. Also you lose points for not making the stick a penis head. This is the reversible one where you can move which side the stick is on right?
Binged All Of Gundam In 4 Years, 1 Week and All I Got Was This Stupid Mask
FF XIV: Walked to the End
Started Legend of the Galactic Heroes (14/07/23), pray for me.
Pretty much. All I have to do if flip the Button's panel upside down - rotate it 180. I even have someone playing on it like that.Let me try to find it...Found it!
Big
Last edited by Epiren; June 23rd, 2015 at 01:06 PM.
Since I'm the most active here, I'll just announce this: I'll be moving to China in the next week, so I probably won't be able to make new sticks for a while. Sorry, my Super Unicorn Deluxe Pinata Stick, with its rotating horn being the joystick, will have to be delayed for a while. But to end on a lighter note, here's the concept for my next stick:
My God, it's full of stars!
P.S. If you have any interesting ideas or concepts, I'll see if I can make them when I get settled.
Screw that.
So after playing for a bit here in China, it turns out that my current stick's shape is rather uncomfortable. I, after all, stick the stick between my legs for better grip, but the wide box shape is really doing a number. Ergo! New concept!
(Done in SketchUp)
Top
Not colored
Colored
What do you think? (Personally, I was thinking more of a mahogany color, but Sketchup didn't have it
Note: Imgur is banned in China. The more you know.
Last edited by Epiren; July 15th, 2015 at 06:27 AM.
Broken Links.
Binged All Of Gundam In 4 Years, 1 Week and All I Got Was This Stupid Mask
FF XIV: Walked to the End
Started Legend of the Galactic Heroes (14/07/23), pray for me.
God **#**^@!!$!
Is there an image host you'd like to recommend? Since I went through 4 ish and apparently they all don't work. >:[
Alright, I got a VPN, so here's a model for my next stick. I've based this off of the Hori RAP 4 Premium, with a number of changes that you probably can't see. The most important though is the bottom chamfer - holding a stick between my legs hurts after a while, so the shape supposedly is going to fix that.
Material wise, I am planning on using a type of plastic instead of wood. This is in no way related to the current ban of power tools on me, nosirree. For the walls, I was thinking of 25mm thermoplastic (gotta see what's around), with the top and bottom panels being 1.5mm of sheet metal. The top panel will also have 2-4 layers of 2mm thermoplastic similar to Wonderflex.
Other View
Color Options
And I made some sample artworks. Which do you think I should use? Keep in mind these are all drafts, so I didn't exactly use high res pictures:
Artwork
Last edited by Epiren; August 9th, 2015 at 05:12 AM.
Reply With Quote
